|
东莞市颖鑫电子科技有限公司为你详细介绍：拨动开关规格书，拨动开关技术参数，拨动开关生产注意事项！
东莞市颖鑫电子科技有限公司规格书
SPECIFICATION |
||||||||||
| DESIGNATION 系列:拨动开关 | ||||||||||
| MODULE NO. 型号: | ||||||||||
| 1. RATING 额定值: 0.3A DC 50V | ||||||||||
| 2. CIRCUIT 回路: 1P 2T | ||||||||||
| 3. TIMING 切换类型: S(SHORTING)/ Non-shorting | ||||||||||
|
4. STANDARD TEST CONDITIONS SHALL BE 5 TO 35℃ IN TEMPERATURE AND 45 TO 85% IN HUMIDTY. |
||||||||||
| 温度5-35℃,湿度45-85%标准状态下测试. | ||||||||||
| 5. OPERATING TEMPERE RANGE -- 10 TO 60℃ | ||||||||||
| 温度-10~60℃环境内使用. | ||||||||||
| ITEM 项目 | TEST CONDISTION 测试条件 | PERFORMANCE 规格 | ||||||||
| 6. ELECTRONICAL PERFOORMANCE 电气性能 | ||||||||||
| 6.1 |
CONTACT RESISTANCE 接触阻抗 |
Being measured at 1kHz small current contact resistance meter. 在1KHz小电流下测量 |
30MΩ max. 30毫欧以下. |
|||||||
| 6.2 |
INSULATION RESISTANCE 绝缘阻抗 |
Measurements shall be made following application of DC 500V potential across terminals and across terminals and frame for 1 minrte. 在端子之间和端子与壳之间加DC 500V 条件下, 持续1分钟测量. |
100MΩmin.. 100毫欧以上 |
|||||||
| 6.3 |
WITHSTAND VOLTAGE 耐电压 |
AC 500V(50Hz or 60Hz)shall be applide across terminals and acoss teminals and frame for one minrte 在端子之间和端子与壳之间加AC 500V (50Hz或60Hz)条件下,持续1分钟表测量. |
There shall be no breakdown. 无击穿现象出现. |
|||||||
| 7. MECHANICAL PERFORMANCE 机械性能 | ||||||||||
| 7.1 |
OPERATING FORCE 动作力 |
MEASURE AT THE POINT 3mm FROM THE TIP OF THE ACTUATOP （KNOB） 在距离推杆前端3mm作测定点. |
250gf±50gf | |||||||
| 7.2 |
TERMINAL STRENGTH 端子强度 |
A static force of 500gf being applied in one direction the tip of the terminal for 1 minute. 一个500克之静电负荷施加于端子顶部的一个方向 持续1分钟. |
There shall be no sign of damage mechanically and electrically. 无任何迹象显示机械及 电器性能之损坏. |
|||||||
| 7.3 |
ACTUATOR STRENGTH 推杆强度 |
A static load of 1kgf being applied in one direction of actuator for one min. 一个1公斤静负荷施加于推杆之一个方向持续 1分钟. |
The defromation shall not be extrene and the actuator shall machanically work normally 推杆无变形,可以正常操作 |
|||||||
本拨动开关规格书由颖鑫电子科技有限公司内部资料！只适合本公司产品，请勿与市场上开关通用。详情请登入：南平颖鑫电子拨动开关厂家
